Electrical

  • Flashers Flashers
  • Ignition Ignition
  • Switches Switches
  • Turn Signal Turn Signal
  • Master Battery Disconnect On/Off Kill Switch Semi-Truck Freightliner Peterbilt
    New Heavy Duty Master Battery Disconnect On/Off Kill Switch with Red HandleCAN BE USED ON ALL SEMI-TRUCKS - FREIGHTLINER, KENWORTH, MACK, PETERBILT, ETC...Battery Disconnect Switch - 2 Terminal Single Pole Single Throw Can be used on Race Cars, Street Rods, Boats, Heavy Machinery or anywhere else you may need a master battery on/off switch. Can be used on 6 Volt, 12 Volt, 24 Volt, or 36 Volt Electrical Systems. The lever is removable so you can make your own  push/pull system if you prefer or if its required. Manual battery disconnect switch with a bright red handleEasier to find in an emergency Mounts studs are 3/8" in diameter. Ratings: 180 amps continuous - 1000 amps intermittent Made of Heavy Duty Die Cast Metal Lever is spring loaded and vibration resistantMounting Hole Size: 0.730" Body Diameter (At largest Point): 2.647" Body Depth (From end of threads to lock washer): 2.980" Overall Depth: 4.216" CROSS REFERENCE: Manufacture Part NumberLONGACRE 45750 AIRTEX AUTOMOTIVE DIVISION   1S2545 BWD AUTOMOTIVE    S678 BWD AUTOMOTIVE    S9905 COLE HERSEE 2484 M-288 M284 ECHLIN SW34 GP SORENSEN BS4 KEMPARTS UL4D NAPA SW34 NIEHOFF      UN129B NIEHOFF      UN129E NIEHOFF      UN77291 POLLACK 51-902, 51-302 STANDARD MOTOR PRODUCTS (SMP) DS248 WELLS    542601 WELLS    SW1765 WELLS    SW273
    Not rated yet
    • $27.95
  • 2 Pin Prong Terminal LED Flasher Electronic Relay Switch Turn Signal Light 12V
    (1)  2 Terminal 12V LED Electrical Flasher New 2-prong (2 terminal with ground wire) 12 Volt LED Flasher. Flasher is designed to replace stock turn signal flasher on most 1955 to present cars and trucks with 2 prong 12v systems. Flasher has NEGATIVE ground (flasher will NOT work with early 6v POSITIVE ground cars/truck or motorcycles). Replacement of the stock flasher is usually needed in order for the LED turn signals to operate as intended. Solves: hyper flashing, burnt out bulb indication, or non flashing when using led lights and led light bulbs. We are also including a FREE "reverse polarity" adapter. If your turn signal flasher dock has the wires reversed, no need to disconnect, switch, and reinstall wires. Simply attach the adapter to the end of the flasher. These flashers will also work with stock turn signals, so if you change back to stock lights, there will be no need to swap out the flasher We also offer 3-prong LED flashers for most pre-1955 vehicles that have been converted to 12v Solve Turn Signal Problems: Hyper Flashing, No Flashing, or Burnt Out Bulb Indication when using LED Lights and LED Bulbs 2 Terminal Flasher / 2 Prong with Ground Wire Use with LED lights Max 20 Amps
    Not rated yet
    • $14.95
  • 2 Pin Prong 12V Terminal Relay Electronic LED Flasher Switch Turn Signal Light
    (1)  2 Terminal 12V LED Electrical Flasher New 2-prong (2 terminal with ground wire) 12 Volt LED Flasher. Flasher is designed to replace stock turn signal flasher on most 1955 to present cars and trucks with 2 prong 12v systems. Flasher has NEGATIVE ground (flasher will NOT work with early 6v POSITIVE ground cars/truck or motorcycles). Replacement of the stock flasher is usually needed in order for the LED turn signals to operate as intended. Solves: hyper flashing, burnt out bulb indication, or non flashing when using led lights and led light bulbs. We are also including a FREE "reverse polarity" adapter. If your turn signal flasher dock has the wires reversed, no need to disconnect, switch, and reinstall wires. Simply attach the adapter to the end of the flasher. These flashers will also work with stock turn signals, so if you change back to stock lights, there will be no need to swap out the flasher We also offer 3-prong LED flashers for most pre-1955 vehicles that have been converted to 12v Solve Turn Signal Problems: Hyper Flashing, No Flashing, or Burnt Out Bulb Indication when using LED Lights and LED Bulbs 2 Terminal Flasher / 2 Prong with Ground Wire Use with LED lights Max 20 Amps
    Not rated yet
    • $14.95
  • 2 Pin Prong 12V Terminal Electronic Flasher LED Turn Signal Light Switch Relay
    (1)  2 Terminal 12V LED Electrical Flasher New 2-prong (2 terminal with ground wire) 12 Volt LED Flasher. Flasher is designed to replace stock turn signal flasher on most 1955 to present cars and trucks with 2 prong 12v systems. Flasher has NEGATIVE ground (flasher will NOT work with early 6v POSITIVE ground cars/truck or motorcycles). Replacement of the stock flasher is usually needed in order for the LED turn signals to operate as intended. Solves: hyper flashing, burnt out bulb indication, or non flashing when using led lights and led light bulbs. We are also including a FREE "reverse polarity" adapter. If your turn signal flasher dock has the wires reversed, no need to disconnect, switch, and reinstall wires. Simply attach the adapter to the end of the flasher. These flashers will also work with stock turn signals, so if you change back to stock lights, there will be no need to swap out the flasher We also offer 3-prong LED flashers for most pre-1955 vehicles that have been converted to 12v Solve Turn Signal Problems: Hyper Flashing, No Flashing, or Burnt Out Bulb Indication when using LED Lights and LED Bulbs 2 Terminal Flasher / 2 Prong with Ground Wire Use with LED lights Max 20 Amps
    Not rated yet
    • $14.95