Headlight Components

Products: 112 of 58
  • Breather Patch 20mm Set of 4 Diode Dynamics
    Keep it dry! These breather patches allow air to vent out of a headlight, but block moisture from coming in. This is a big help in preventing condensation from building up inside. Available in packs of 4 or 40 units, the circle stickers are 20mm in diameter, or just over 3/4 inches. They are designed to be placed over a 1/2 inch hole. We recommend using two per lamp to provide maximum airflow. To install, drill a 1/2 inch hole on your lamp. We recommend placing at the side, but you can choose anywhere that has a flat surface. Clean the hole and stick on the patch, holding firmly for 5 seconds to ensure good adhesion. That's it!Details: 20MM or 3/4 Inch Diameter Black Sold at Four(4)
    • $4.95
    10 left in stock. Backorder available
  • 5 LED "GUIDE" Top Mount - Amber LED/Clear Lens | Headlight Components
    5 LED Top Mount Light for "GUIDE" Style Headlight Amber LED w/ Clear Lens, Epoxy Sealed Only Fits United Pacific Headlight Bezel with Top Mount Signal1156 Plug (Hard Wired)
    • $10.28
  • D2S Bulb Adapter Pair Diode Dynamics
    These are accessory cables needed to connect D2S bulbs to a standard HID ballast output, for custom HID installations. Priced per pair.Your order includes: 2 Precision HID D2S Adapter Cables What's Included Quantity: Two (2) Warranty: 3 year warranty 100 percent Satisfaction Guarantee
    • $14.95
    10 left in stock. Backorder available
  • 5 LED Dual Function "GUIDE" Headlight Signal - Amber LED/Amber Lens | Headlight Components
    5 LED Signal Light Dual Function Top Mount Light for "GUIDE" Style Headlight 5 Amber LED w/ Amber Lens Hard Wired with 1157 Plug
    • $15.79
  • 5 LED Dual Function "GUIDE" Top Mount - Amber LED/Clear Lens | Headlight Components
    5 LED Dual Function Top Mount Light for "GUIDE" Headlight Amber LED w/ Clear Lens Hard Wired with 1157 Plug
    • $15.79
  • Butyl Headlamp Sealant Single Diode Dynamics
    Easy to work with. Properly reseal any headlamp or tail lamp and protect against moisture ingress with Diode Dynamics Butyl Headlight Sealant! This new and improved sealant rope was designed specifically for headlamps, with a firmer composition than auto-store windshield glue. This makes it easy to work with, without causing a sticky mess. Each roll comes with 20 feet of butyl, enough to reseal two large headlamps. Protection from moisture. Use it to reseal any headlamp after installing Diode Dynamics LED products! Warm it up a bit, place it into the headlight channel, and clamp together while heating, making sure the lens is fastened to the housing. With a little practice, you'll have a factory-quality seal, with quality butyl that will protect against moisture ingress for years to come. Experience. After over a decade in business, Diode Dynamics is the most trusted name in automotive LED lighting. Unlike every other LED distributor, we manufacture and engineer products ourselves in the United States, for high quality and fast time-to-market of the newest and brightest LED technologies. We pride ourselves in offering only quality LED products, that will exceed your expectations.Features Butyl Headlamp Sealant Single Automotive grade butyl sealant Easy to work with, no sticky mess Standard black color 20 feet long (enough to reseal two large headlamps) 7mm diameter, designed to fit directly in headlamp channels What's Included Quantity: One (1) Warranty: 3 year warranty Return Policy: 30-day Return with no restocking fee 100 percent Satisfaction Guarantee Fitment Used to reseal any headlamp or tail lamp Specifications Length: 20 feet Diameter: 7mm Color: Black Operating Temperature: No Weight (lb): 1.5250
    • $17.95
    10 left in stock. Backorder available
  • EP29 LED Turn Signal Flasher Diode Dynamics
    Hyperblink Fix. Why do you need this module? When your factory turn signal bulbs go out, your vehicle's flasher senses that less power is being used, and it will blink the turn signals quickly to alert you. Since LED bulbs use less power, you get the same fast blinking, known as hyperblinking, even though the LEDs are functioning just fine. Basically, your car thinks the bulbs went out! To slow down the blinking to regular speed, you can add resistors to increase the circuit's power consumption again. However, whenever possible, replacing the flasher with a module like this is the easiest option. Simply unplug your original flasher from under the dash, and swap it with this one to prevent hyperblinking. Quality. The flashers distributed by Diode Dynamics are produced by industry leaders such as Novita. Watch out for generic cheap flashers, as many are slightly too large and may not fit properly in the socket.Features: Compatible with LED bulbs Prevents hyperflash errors Simple swap for original module Direct fitment and proper sizing What's Included In the Box: One LED-compatible flasher relay module Three-year replacement warranty Quantity: One (1) Warranty: 3 year warranty Return Policy: 30-day Return with no restocking fee 100 percent Satisfaction Guarantee Fitment: Plug and play, direct fitment in your vehicle Direct swap for your original flasher module Specifications: Operating Voltage: 9-16V Operating Temperature: -40C to 85C (-40F to 185F) Connector(s): OEM-Size Plug and Play Weight (lb): 0.1250
    • $24.95
    10 left in stock. Backorder available
  • Chrome "GUIDE" Headlight Signal Housing | Headlight Components
    Top Signal Light Housing for "GUIDE" Style Headlight Available in Chrome
    • $26.59
  • Stainless "GUIDE" Headlight Signal Housing | Headlight Components
    Top Signal Light Housing for "GUIDE" Style Headlight Available in Stainless Steel
    • $29.39
  • Bixenon HID Adapter 9004 Pair Diode Dynamics
    When installing HIDs in a dual-filament application, the original factory power signal must be separated into main power for the ballast, and a high beam signal to trigger the bixenon bulb, switching from low beam to high beam. Normally, this is accomplished with a bixenon relay, which connects to the battery and runs to each headlight. However, these can be unreliable as the relay fails over time, and cumbersome to install. These bixenon adapters are a modern, reliable alternative to the traditional wire harness relay. They do not require extra wiring- it's just an adapter! Plug one side into your factory bulb socket, then plug the other side into your HID ballast and bixenon HID bulb. The adapter will power the ballast, and quickly change from low to high beam when you flip the switch in your vehicle. These adapters are fully encapsulated for maximum reliability, and are compatible with all 35W CAN-BUS HID ballasts. Select the size based on the input power signal - H4/9003, H13, 9004, or 9007. The output wires are standard 9006 power to plug into the ballast, and a rectangular 2-pin standard high beam solenoid connector. Included in your order is two adapters, one for each side of your HID kit. Please make sure to select the correct option for bulb size, corresponding to your headlight bulb size. All items are covered by Diode Dynamics 30 days satisfaction guarantee as well as Diode Dynamics 3-year limited warranty.What's Included Bixenon Adapter 9007 Pair Quantity: Two (2) Warranty: 3 year warranty 100 percent Satisfaction Guarantee
    • $29.95
    10 left in stock. Backorder available
  • Bixenon HID Adapter 9007 Pair Diode Dynamics
    When installing HIDs in a dual-filament application, the original factory power signal must be separated into main power for the ballast, and a high beam signal to trigger the bixenon bulb, switching from low beam to high beam. Normally, this is accomplished with a bixenon relay, which connects to the battery and runs to each headlight. However, these can be unreliable as the relay fails over time, and cumbersome to install. These bixenon adapters are a modern, reliable alternative to the traditional wire harness relay. They do not require extra wiring- it's just an adapter! Plug one side into your factory bulb socket, then plug the other side into your HID ballast and bixenon HID bulb. The adapter will power the ballast, and quickly change from low to high beam when you flip the switch in your vehicle. These adapters are fully encapsulated for maximum reliability, and are compatible with all 35W CAN-BUS HID ballasts. Select the size based on the input power signal - H4/9003, H13, 9004, or 9007. The output wires are standard 9006 power to plug into the ballast, and a rectangular 2-pin standard high beam solenoid connector. Included in your order is two adapters, one for each side of your HID kit. Please make sure to select the correct option for bulb size, corresponding to your headlight bulb size. All items are covered by Diode Dynamics 30 days satisfaction guarantee as well as Diode Dynamics 3-year limited warranty.What's Included Bixenon Adapter 9007 Pair Quantity: Two (2) Warranty: 3 year warranty 100 percent Satisfaction Guarantee Specifications Measured Lumens: 3200 (per bulb) Operating Voltage: 9-16V Operating Temperature: -40C to 85C (-40F to 185F) Connector(s): OEM-Size Plug and Play
    • $29.95
    10 left in stock. Backorder available
  • Bixenon HID Adapter H13 Pair Diode Dynamics
    When installing HIDs in a dual-filament application, the original factory power signal must be separated into main power for the ballast, and a high beam signal to trigger the bixenon bulb, switching from low beam to high beam. Normally, this is accomplished with a bixenon relay, which connects to the battery and runs to each headlight. However, these can be unreliable as the relay fails over time, and cumbersome to install. These bixenon adapters are a modern, reliable alternative to the traditional wire harness relay. They do not require extra wiring- it's just an adapter! Plug one side into your factory bulb socket, then plug the other side into your HID ballast and bixenon HID bulb. The adapter will power the ballast, and quickly change from low to high beam when you flip the switch in your vehicle. These adapters are fully encapsulated for maximum reliability, and are compatible with all 35W CAN-BUS HID ballasts. Select the size based on the input power signal - H4/9003, H13, 9004, or 9007. The output wires are standard 9006 power to plug into the ballast, and a rectangular 2-pin standard high beam solenoid connector. Included in your order is two adapters, one for each side of your HID kit. Please make sure to select the correct option for bulb size, corresponding to your headlight bulb size. All items are covered by Diode Dynamics 30 days satisfaction guarantee as well as Diode Dynamics 3-year limited warranty.What's Included Bixenon Adapter H13 Pair Quantity: Two (2) Warranty: 3 year warranty 100 percent Satisfaction Guarantee Specifications Measured Lumens: 3200 (per bulb) Operating Voltage: 9-16V Operating Temperature: -40C to 85C (-40F to 185F) Connector(s): OEM-Size Plug and Play
    • $29.95
    10 left in stock. Backorder available
Products: 112 of 58
  • Bogg Bag XL You Navy Me Crazy Blue Ultimate Beach Tote Go Anywhere With 2 Pouch
    Bogg Bag Cooler COMBO Large Original Beach Tote Navy Blue NWT AuthenticUltimate Tote w/ Cooler and Drink Caddy Get all 3! The perfect combination for the beach, boat or ballgames.The Ultimate Tote â€“ Roomy and it won't tip over. Tough plastic is easy to rinse off. Includes 2 removable zip pouches. Bogg® Brrr Cooler â€“ Insulated insert fits snug inside the tote. Durable, soft-sided polyester exterior. Zip closure and adjustable shoulder strap. Ice packs recommended. Navy.Cup Caddy â€“ Convenient size holds most cans and bottles. Coral.
    • $89.95
    2 left in stock.
  • 10Pc White LED Chrome Modules Motorcycle Chopper Frame Neon Glow Lights Pods Kit
    12V MOTORCYCLE WHITE LED ACCENT LIGHTING. (10) CHROME MODULES WITH 4 WHITE LEDS IN EACH MODULE. TWO SCREW HOLES IN THE ABS CHROME MODULE FOR EASY MOUNTING. White LED Color. Operates from 7V-15V DC. 120 degree viewing angle, 4 LEDs per Light. LED's last longer & use less power (uses 30mA of power @ 12V DC). 4 LED's 5mm (Not SMD LEDs with lens cap). 36" wire leads (Red = positive, Black= negative).
    • $34.95
    Out of stock
  • 8Pc White LED Chrome Modules Motorcycle Chopper Frame Neon Glow Lights Pods Kit
    12V MOTORCYCLE WHITE LED ACCENT LIGHTING. (8) CHROME MODULES WITH 4 WHITE LEDS IN EACH MODULE. ADHESIVE DOUBLE SIDED TAPE ON BACKSIDE AND TWO SCREW HOLES IN THE ABS CHROME MODULE FOR EASY MOUNTING. White LED Color. Operates from 7V-15V DC. 120 degree viewing angle, 4 LEDs per Light. LED's last longer & use less power (uses 30mA of power @ 12V DC). 4 LED's 5mm (Not SMD LEDs with lens cap). 36" wire leads (Red = positive, Black= negative). Plastic Chrome module with 2 mounting holes. Includes double sided mounting tape on backside Measures L=1 1/2" H=3/8" W=3/4" Completely waterproof, safe for wet areas.
    • $20.95
    Out of stock
  • 2x Tape Dispenser Industrial Packing Gun Shipping w/ 6 Rolls 2 Mil 2" x 110yds
    2 -  2" Tape Dispensers with 6 large tape rollsIncludes:1 - 2" Side Load Tape Gun6 Rolls - 2 Mil 2" x 110yds
    • $49.95
    Out of stock
  • Replacement OEM HID Bulbs for 2016-2017 GMC Sierra 2500/3500 Pair 6000K Diode Dynamics
    Upgrade. Upgrade your headlights with our D5A HID replacement bulbs! If your vehicle is equipped with HID headlights these are a perfect direct replacement. While the factory bulbs use 25W of power these bulbs use 35W so they provide an increase in total light output giving you better visibility at night. You can also improve your vehicle's styling with a cooler color temperature. Quality. There are all kinds of HID bulbs on the market but these are the best combination of quality without a high price tag. Manufactured in a fully automated environment they have high output and are DOT/SAE and ECE compliant in arc position and size. Using German quartz and American salts no expense is spared in their construction. This leads to a long reliable life and excellent color. Color. While some HIDs on the market give off a green or purple tint these bulbs will provide a pure white color on the road. These HIDs are available in true accurate color temperatures which we measure at our photometric test lab. The white color created by these bulbs will provide more visible light on the road and won't cause distraction. 4300K is a natural white output as seen on vehicles with factory HIDs. It will not have any blue tint to its color and might appear slightly warm. 5000K is a pure white output without any warm hint and no tint of blue either. 6000K is our most popular color which produces an ice white color. It matches best with most LEDs. Experience. After over a decade in business Diode Dynamics is one of the most trusted names in automotive LED lighting. We directly assemble and engineer our own products in the United States allowing for higher quality and performance with the newest and brightest LED technology. We pride ourselves on offering only the best possible LED solutions. Features: Direct replacement for factory OEM HID headlight bulbs Provides increase in total light output Perfect alignment with easy installation True colors with no variance Color Temperature: 6000K Fits: 2016-2017 GMC Sierra 2500/3500 Sold As: Pair
    • $299.95
    9 left in stock. Backorder available
  • HID Bulb D5A 6000K Pair Diode Dynamics
    Upgrade. Upgrade your headlights with our D5A HID replacement bulbs! If your vehicle is equipped with HID headlights, these are a perfect direct replacement. While the factory bulbs use 25W of power, these bulbs use 35W, so they provide an increase in total light output, giving you better visibility at night. You can also improve your vehicles styling with a cooler color temperature. Quality. There are all kinds of HID bulbs on the market, but these are the best combination of quality, without a high price tag. Manufactured in a fully automated environment, they have high output, and are DOT/SAE and ECE compliant in arc position and size. Using German quartz and American salts, no expense is spared in their construction. This leads to a long, reliable life, and excellent color. Color. While some HIDs on the market give off a green or purple tint, these bulbs will provide a pure white color on the road. These HIDs are available in true, accurate color temperatures, which we measure at our photometric test lab. The white color created by these bulbs will provide more visible light on the road, and wont cause distraction. 4300K is a natural white output, as seen on vehicles with factory HIDs. It will not have any blue tint to its color, and might appear slightly warm. 5000K is a pure white output, without any warm hint, and no tint of blue either. 6000K is our most popular color, which produces an ice white color. It matches best with most LEDs. Experience. After over a decade in business, Diode Dynamics is one of the most trusted names in automotive LED lighting. We directly assemble and engineer our own products in the United States, allowing for higher quality and performance, with the newest and brightest LED technology. We pride ourselves on offering only the best possible LED solutions.Features: Direct replacement for factory OEM HID headlight bulbs Provides increase in total light output Perfect alignment, with easy installation True colors, with no variance Color Temperature: 6000K Sold As: Pair
    • $319.95
    9 left in stock. Backorder available
  • LM487 LED Turn Signal Flasher Diode Dynamics
    Hyperblink Fix. Why do you need this module? When your factory turn signal bulbs go out, your vehicle's flasher senses that less power is being used, and it will blink the turn signals quickly to alert you. Since LED bulbs use less power, you get the same fast blinking, known as hyperblinking, even though the LEDs are functioning just fine. Basically, your car thinks the bulbs went out! To slow down the blinking to regular speed, you can add resistors to increase the circuit's power consumption again. However, whenever possible, replacing the flasher with a module like this is the easiest option. Simply unplug your original flasher from under the dash, and swap it with this one to prevent hyperblinking. Quality. The flashers distributed by Diode Dynamics are produced by industry leaders such as Novita. Watch out for generic cheap flashers, as many are slightly too large and may not fit properly in the socket.Features: Compatible with LED bulbs Prevents hyperflash errors Simple swap for original module Direct fitment and proper sizing What's Included In the Box: One LED-compatible flasher relay module Three-year replacement warranty Quantity: One (1) Warranty: 3 year warranty Return Policy: 30-day Return with no restocking fee 100 percent Satisfaction Guarantee Fitment: Plug and play, direct fitment in your vehicle Direct swap for your original flasher module Specifications: Operating Voltage: 9-16V Operating Temperature: -40C to 85C (-40F to 185F) Connector(s): OEM-Size Plug and Play Weight (lb): 0.1250
    • $64.95
    9 left in stock. Backorder available

Browse by Vehicle